Version 0.97b+ (epr097c.zip)(11/09/02)

• fixed Windows/image for Large font and reduce image files
• fixed little bug Test H/W in ver 0.96C
• add Func. Move Data (Buffer)
• add device P87C51/52/524/528 (Philips)
• fixed Bug Setting config #debugger PIC16F87X (report bug by demek2) (31/07/02)
• add device MX29F001/002/004 (T/B)
• add software protect/unprotect sector for 29F00x (24/08/02) untest
• add PIC16F627A, PIC16F628A
• Fixed bug software protect/unprotect sector for MX29F00x, MX29F040 (06/09/02)
  • test on EN29F002T (read sector status only)
• Fixed bug device FWH/LPC , Upspeed latch address
  • test on 82802AB (get ID/read/verify/erase/program) request Adapter FWH/LPC
• Fixed image jumper setting 28C16 (ver 0.97/a/b) (report bug by ziko)

Version 0.96C (02/07/2002)

• Fixed bug MCS-48/41 inc. delaytime latch address&read data ( Adapter MCS-48/41 ) report bug by ArtKar
• Add device M29F080/016/032 and add Fast mode prog. for ST chip, AMD rev. B
• Add device CAT64C010/020/040 (SPI 16bit ) (untest)
• Fixed little Bug read/verify 24Cxx
• Add Device SDE2526 (I2C)
• Fixed Bug setting DIPSW for 28F256 (DIP32)
• Add device Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command erase/prog.)
  (Bulk Erase Flash Memory with Embedded Algorithms)
• Add device PIC16F873A, PIC16F874A, PIC16F876A, PIC16F877A
• Add device SST37VF512/010/020/040 (3.3V)see Erase data SST27SFxxx)
• Add device AT29C257(DIP32)
• Set priority realtime for Func porg_29Cxxx()
  • test on AT29C020, SST29EE010, W29C011A

• Fixed bug select tWC, tWP
• Fixed bug save dataID&Configs PIC16Fxxx
• Skip witre 0x3FFF in PIC16Fxxx mode (reduce time programming)
• Add on/off Vcc(MCLRE) ICSP mode (PIC16Fxxx) (comment by Luciano)
• Fixed bug erase Func. 28F0x0
• Fixed bug erase 28Fx00,28F001BX-T (erase by MemoryMap) refer intel
• Fixed bug read/verify 28Fx00 and check bit VPP (report bug by momo1)
• Fixed bug program 28Fx00
• Add device 59C11, 59C22, 59C13 (Microwire)
• Add device 85C72,85C82,85C92 (I2C)
• Add device CAT35C102, CAT35C104, CAT35C108 (pullup pin 7 [PE])
• Add device 28F004/008/016 S5(intel), LH28F004,LH28F008 (sharp)
• Add Memorymap for LH28Fxxx (Manufacture SHARP)
• Add device MBM29F004/008/016/320 (Fujitsu chip)
• Add device HY29F080
• Enable device MX28F1000
• Fixed Bug 12Cx5xx by skip wirte PDATA at address 0x1FF (PIC12Cx5x8) , 0x3FF (PIC12Cx5x9,16C505) (report bug by Luciano )
  • Note that some version will have an oscillator calibration value program at 0x1FF (PIC12Cx5x8) , 0x3FF (PIC12Cx5x9)
  • test on PIC12C509A (OTP SMD)
• Add device PIC12CE518/519, 12C508/509JW(EPROM) , PIC16C505 (DIP14)
• Add device AT49F2048A, AT49F4096A, AT49F8192A, AT49F008A
• Add device M87C257 (EPROM address Latch)
• Add device Firmware Hub i82802AB/AC, AT49LW040/080, SST49LF00x,
  LPC flash SST49LF020/040 (Untest All)
  request Adapter Firmware Hub/LPC

• Add Devices MTP EPROM MX26Cx000
• Fixed bug 28Fxxx (erase Func.)
• Enable&Fixed bug PIC 16C62x
• Fixed bug read ID AT89Cx051 (DIP20)
• Fixed Bug setting config PIC16xxxx
• Add select tWC
• Add select tWP
• Add device PIC16C710/711 (test on PIC16C711/JW (EPROM))
• Add Device MX28Fx000
• Add Device AVR 8-bit RISC (test on AT90S2313)
  • read/write/verify (Flash/EEPROM), erase, Lockbit, Fusebit, save/load *. eep
  • AT90S2313 Errata Sheet.pdf
    
    
    
    
• inc. delay time Erase Data 29LV/29C/29F/49Fxxx and check DQ7
• Add Function Fast mode Fujitsu Chip Test On MBM29LV160T-90
  • Normal program = 18.54 minute .
  • Fast progamming = 13.15 minute .
  • Fast mode programming (Fujitsu Chip) = 8.36 minute.

• Add Devices MCS-41 (P8041/8042/8741/8742) request Adapter MCS-48/41
  • Test On Chip P8042(ROM),P8742 (EPROM)
• Fixed bug Menu 24C64-24C512
• Fixed bug 28C256
• Add Decive AT28C256 (page write)
• Add decive 27C400/800/160/322

• Add Devices MCS-48 (P8048/8049/8050/8748/8749) request Adapter DIP32 to MCS-48
  • Test On Chip P8049(ROM),P8749(OTP),D8749(EPROM)
• Fixed Bug Read/Verify/Program EPROM AM27Cxxx (AMD)
• Fixed little Bug Load setting MCS-51
• Add Decive W27C040

• Fixed DIPSW setting for 27C080 (Error in windows version)
  • Verify decvice by Toralf (AT27C080)
• Fixed Bug Menu select W27C020
  • test on Chip W27C020,W27C010 . ERASE/write/read/verify
• Fixed little bug 24Cxxx
• reduce time write/read/verify 24C32 - 24C512 (page wirte)
  • Test on Chip 24LC32, 24LC256 (9 second)
• Inc. tWP,tWC device LE28F4001
• Fixed little bug unprotect Chip LE28F4001
  • verify device LE28F4001, SST28F040A (TSOP32),AM29F040 by EZo
  • use Ezoflash ver2.0
• Enable selected unprotect sector temporary (29Fx00) for erase/wirte by on Vpp at Pin 1(#Reset)

• Add Device 25Cxxx SPI (Full support) test on 25LC640 (microchip)
• Device 27x32,27x512,27x080.It will write all data before verify data (Fixed problem on/off Vpp and reduce time programming

Version 0.93c (23/10/2001)
Serial Programming PICxxx, 25xxx try use ( ic-prog.exe ) www.ic-prog.com

• Fixed bug Device 27256
• Device 27C512, 27C080 (increase delay time off Vpp(OE low) before read data (Burn mode)
• Fixed bug Menu 27xxx
  • test on 2716(25V), 27C16(12.5V), 2732(21V),
  • 27C64A, HN27256,D27256, 27C256, NM27C512, TMS27C512, M27C512, D27C512

• PIC 16Cxxx
• Add Device PIC16F870-877 (ICSP), PIC16F627/628 ( tprog = 5mS/word )
  • Test on PIC16F872, PIC16F876, PIC16F877 ( ICSP connector )
• Fixed bug Display Buffer (prog/eeprom)
• Modify new func. IC-setting
• Add read Device ID ( 2006h ) PIC mode.
• Modify new function Auto save/Load configs
• Add select command 2AAA,5555,2AAA,...(29Fxxx) and AAAA,5555,AAAA,... (29Fx00)
• Add device 29F160,29F320
• New menu select Device
• Fixed bug func. offset (data+offset > Device size), Read data+offset, ...
• Device i28F001BX-T (test on chip i28F001BX-T120)
  • Add message box ( short PIN [1]<->[30] or setting jumper (PCB3A or PCB3 modify))
  • Fixed error setting DIPSW
  • Fixed bug read ID address 0x0001
• New setting DIPSW&jumper for the AT29C256 (PCB3/PCB3A)

• Change compiler BCB 3.0 to 4.0
• Add Function repair H/W
• Add Protect/unprotect MXIC (Add code by carlonb@libero.it)
• Add Function Romident (Add code by Mike coates)
• Add Fast Programming 29Fxxx,39Fxxx,49Fxxx,29Fx00 (reduce time programming30-40%)
• Fixed little Bug "mPIC_mask="
• Fixed Bug Func. Device 28Cxxx
• Fixed little Bug Func. Skip write 0xFF
• Display Jumper PCB3 device DIP24 (2716,2732,2816,6116)

• Fixed Bug all function microchip PIC and Add Func. Check blank ,edit ID
  
  • Test on PIC16F84, PIC16F84A, PIC12C509/JW (eprom)
• speed up Programming PIC16F84A delay 5mS/word
• Add Func. swap byte,invert DATA
• Fixed Bug check type 16 addition
• Speed Up Prog. AM29Fx00,29/39/49Fxxx,29/49F00x,28Fx00 by skip write Data 0xFF
• Fixed error command Write SST28SF040A
• Add Device LE28F4001 (4Mbit)
  • SST28SF040A Erase data by erase Chip Function,(delay 400ms)
  • LE28F4001 Erase data by sector-erase Function, ( delay 4 ms/sector),
    • sector size = 256 byte (2048 sector x 4 ms = 8.192 sec)

• Add device 29Cxxx (sector programming) (20/05/01)
• Add device 29/49F00x
• Add device AT89Cx051(DIP 20PIN)
• Fixed error Get ID Flash memory Winbond and SST
  Command seq. electronic ID
  • AT29Cxxx (55,AA,90)
  • W29EExxx,PH29EE0X0 (55,AA,80,55,AA,60)
• Fixed bug Func. DS12xx, loadsetting, etc..
• Add MCS-51 (89Cxx) (23/05/01)
• Fixed bug message (Error at adress 0xxxx, chip xx, buffer xx)
• Fixed Error show Number DIPSW ( some ver. WIN9x) (25/05/01)
• SpeedUp Prog. EPROM 27C256,27C010,27C020,27C040
  (Vpp not off during Verify data in Program mode [reduce time delay 160 us/byte to 10us/byte])
• Add select tWC in Device 29Cxxx
• Enable 29Fx00 (12/06/01)
• Add Select sector size 29Cxxx (03/08/01)
• Programmer & Lock Bit MCS-51
• Add Save Lockbit (14/08/01)
• Enable set Offset address
• Add Device SST27SFxxx ,SST28SF040A, SST89C54/58, IS89C52 (26/08/01)
• SST28SF040A Combine Command software Data Unprotect in Function Program & Erase Chip (29/08/01)
• Fixed Bug Function verify 27Cxxx, 27Exxx

• New interface ref. PCB3
• speed up read,write,verify
• New code 29/39/49Fxxx
• New code 28Cxxx
• Dynamic Address (A0 -- > Axx) (increase speed overall (read,write,verify,...))
• add Prog CHIPS 28Fx00 Flash memory 16 bit i28Fx00 [TSOP48] (read,write,erase,verify[byte mode]
• Fixed sometime Error (Function. read,write,verify, Empty EPROM 27C010,27C020
• New code EPROM 27CXXX. (13/05/01)
• add Prog CHIPS 29Fx00 read,write,erase chip,Get ID,verify [byte mode])(14/05/01)
• Enable Get Electronic ID (Get ID 29/39/49/89/90)
• Add menu Device select (map popup Menu)
• Fixed Bug verify 24Cxx (16/05/01)
• New code 93Cxx
• Add function Erase (erase all) Chip 93Cxx
• Add device SRAM 6116,6264,62256,628128
• Add device DS12xx (Nonvolatile SRAM) [shift address (swap) A14 -> A15 -> A18]
• Add swap Display DIPSW&picture (willem(PCB) and PCB3)

---

HOME

---