Welcome to Amptron.Com - PM-7900 Online Manual Page 2
Click here to find out how you can buy an Amptron Motherboard!

Online Manual Menu Bar
PM-7900 JUMPER SETTINGS
 J2 - KEYBOARD CONNECTOR
 J5 - HDD LED CONNECTOR 
 J6 - RESET SWITCH CONNECTOR 
 J7 - INTERNAL/EXTERNAL BATTERY SELECTORS 
 J8 - KEYLOCK & POWER LED CONNECTOR 
 J9 - SPEAKER CONNECTORS 
 JP4 - FLASHROM VOLTAGE SELECTOR
 JP5 - AT BUS CLOCK SELECTOR
 JP6 - SLEEP SWITCH CONNECTOR 
 JP7 - DIMM SOCKET VOLTAGE SELECTORS 
 JP10 & JP11 - CPU SPEED SELECTORS
 JP12 & JP13 - CPU INTERNAL CLOCK SPEED SELECTORS
 JP14 - CPU VOLTAGE REGULATOR OUTPUT SELECTORS 
 
J2 - Keyboard Connector
====================================
PIN         CONNECTOR TYPE 
------------------------------------
 1            kEYBOARD CLOCK
 2            kEYBOARD DATA
 3            NC
 4            GROUND
 5            +5VDC
====================================
J5 - HDD LED Connector
====================================
PIN         ASSIGNMENT 
------------------------------------
 1            +5V
 2            ACTIVE LOW
====================================
J6 - Reset Switch Connector
====================================
JUMPER      ASSIGNMENT 
------------------------------------
 OPEN         NORMAL MODE
 SHORT        RESET SYSTEM
====================================
J7 - Internal/External Battery Selectors
========================================
JUMPER      PIN      ASSIGNMENT 
----------------------------------------
 2 - 3                  INTERNAL BATTERY
 3 - 4                  CLEAR CMOS
             1 & 4      EXTERNAL BATTERY
========================================
J8 - Keylock & Power LED Connector
====================================
PIN         ASSIGNMENT 
------------------------------------
 1            LED OUTPUT
 2            NC
 3            GROUND
 4            KEYLOCK
====================================
J9 - Speaker Connectors
====================================
PIN         ASSIGNMENT 
------------------------------------
 1            DATA OUT 
 2            NC
 3            GROUND
 4            +5V
====================================
JP4 - FlashROM Voltage Selector
==============================================
JUMPER      ASSIGNMENT 
----------------------------------------------
 OPEN         EPROM & 5 VOLT FLASH PROGRAMMING
 SHORT        12 VOLT FLASH PROGRAMMING
==============================================
JP5 - AT Bus Clock Selector
====================================
CPU CLOCK    JUMPER     STATE   
------------------------------------
  66MHz         1-2      PCI CLK/4
  60MHz         1-2      PCI CLK/4
  50MHz         2-3      PCI CLK/3
====================================
JP6 - Sleep Switch Connector
====================================
JUMPER      ASSIGNMENT 
------------------------------------
 OPEN         NORMAL MODE 
 1 - 2        SLEEP MODE ON
====================================
JP7 - DIMM Socket Voltage Selectors
===============================================
JUMPER      STATE      DRAM TYPE INSTALLED 
-----------------------------------------------
 1 - 2        5.0V        FP MODE/EDO DRAM
 2 - 3        3.3V        SDRAM (SYNC. DRAM)
===============================================
JP10 & JP11 - CPU Speed Selectors
=======================================
CPU SPEED   JUMPER J10   JUMPER J11  
---------------------------------------
  66MHz         SHORT          OPEN 
  60MHz         OPEN           SHORT 
  50MHz         SHORT          SHORT 
=======================================
JP12 & JP13 - CPU Internal Clock Speed Setting
===================================================
INTEL       CYRIX       AMD       JP12    JP13
---------------------------------------------------
 X1.5       RESERVED     X1.5       OPEN     OPEN
 X2.0        X2.0      RESERVED     SHORT    OPEN
 X2.5       RESERVED   RESERVED     SHORT    SHORT
 X3.0       RESERVED   RESERVED     OPEN     SHORT
===================================================
NOTE: CPU Internal Clock Speed = External Input Clock x Multiplier (table above)
JP14 - CPU Voltage Regulator Output Selectors
====================================
JUMPER      VOLTAGE 
------------------------------------
 2 - 3        3.3 vOLT (STD/VR) 
 1 - 2        3.5 VOLT (VRE)
====================================
VRM Info Here!
 

Return to the Main Menu

 
[ Main Menu | [ Products | Tech Support | Download ]
[ Credit Info | RMA Online | Company Profile

(C) 1997 Amptron International Inc
Specifications subject to change without notice
All trade marks and brand names are acknowledged 
as belonging to their respective owners.

Comments, Suggestions, Email the Webmaster
  
 
A Symbol of Value!
 
 
 SYSTEM BOARD
 

ProductsTechnical SupportDownloads