DOCUMENT:Q151760  20-FEB-2002  [winnt]
TITLE   :Error 20091 When Client Dials RAS Server Using TCP/IP
PRODUCT :Microsoft Windows NT
PROD/VER::3.5,3.51,4.0
OPER/SYS:
KEYWORDS:kbusagekbfaq

======================================================================
-------------------------------------------------------------------------------
The information in this article applies to:

 - Microsoft Windows NT Workstation versions 3.5, 3.51, 4.0 
 - Microsoft Windows NT Server versions 3.5, 3.51, 4.0 
-------------------------------------------------------------------------------


SYMPTOMS
========

Windows NT, Windows 95, or third-party PPP clients fail to connect to your
Windows NT Remote Access Service (RAS) server using the TCP/IP protocol.

In the System Log of the Event Viewer on your Windows NT RAS server, you see the
following error message:

   Event ID: 20091
   Source: RemoteAccess
   Type: Error
   Description: The Remote Access Server was unable to acquire an IP Address from
   the DHCP Server to be used on the Server Adapter. Incoming users will be
   unable to connect using IP.

CAUSE
=====

This behavior can occur if either of the following conditions exist:

 - You are using DHCP on your network, but you have not created an active scope
   that includes addresses from the same subnet as the subnet of the RAS
   server's network card.

 - Your RAS server is configured to use DHCP to assign remote TCP/IP client
   addresses (the default option), however, there is no DHCP server on your
   network.

RESOLUTION
==========

If there is a DHCP Server on your network, make sure you have an active scope on
your DHCP server that includes addresses from the same subnet as the subnet of
the RAS server's network card. For information on creating and activating scopes
using DHCP Manager, refer to DHCP Help.

If there is no DHCP server on your network, configure RAS to use a static address
pool to assign remote TCP/IP client addresses by performing the appropriate
method below:

Windows NT 4.0
--------------

1. In Control Panel, double-click Network, click the Services tab, and then
   double-click Remote Access Service.

2. Click Network, click the TCP/IP check box under Server Settings to select it,
   and then click Configure.

3. Click Use Static Address Pool, set the Begin and End addresses, and then
   click OK.

Windows NT 3.51 and earlier
---------------------------

1. In Control Panel, double-click Network, and then double-click Remote Access
   Service.

2. Click Network, and then click Configure (for TCP/IP) under Server Settings.

3. Click Use Static Address Pool, set the Begin and End addresses, and then
   click OK.

Additional query words: 3.50 3.51 4.00 20090 736 629 negotiate compatible

======================================================================
Keywords          : kbusage kbfaq
Technology        : kbWinNTsearch kbWinNTWsearch kbWinNTW400 kbWinNTW400search kbWinNT351search kbWinNT350search kbWinNT400search kbWinNTW350 kbWinNTW350search kbWinNTW351search kbWinNTW351 kbWinNTSsearch kbWinNTS400search kbWinNTS400 kbWinNTS351 kbWinNTS350 kbWinNTS351search kbWinNTS350search
Version           : :3.5,3.51,4.0

=============================================================================

THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

Copyright Microsoft Corporation 2002.