SOFTPAQ NUMBER: SP4716 PART NUMBER: 276549-001 PART NUMBER: 276550-001 PART NUMBER: 276551-001 FILE NAME: N/A TITLE: OS/2 Support Software Diskette from Compaq VERSION: 3.01 Rev.A LANGUAGE: English CATEGORY: Drivers/Servers PRODUCTS AFFECTED: Compaq Servers OPERATING SYSTEM: IBM OS/2 v2.x IBM OS/2 Warp v3.0 IBM OS/2 Warp Connect 3.0 IBM OS/2 for SMP v2.11 IBM OS/2 Warp 4.0 IBM OS/2 Warp Server 4.0 IBM OS/2 Warp Server Advanced 4.0 IBM OS/2 Warp Server Advanced with SMP 4.0 SYSTEM CONFIGURATION: One of the above operating systems. EFFECTIVE DATE: March 06, 1998 ELECTRONIC DISTRIBUTION ALLOWED: YES SUPERSEDES: SP3080 DESCRIPTION: This Softpaq creates the OS/2 Support Software Diskettes for Compaq Version 3.01 Rev A. For complete information on changes and enhancements to the OS/2 2.x Support Software diskette, see WHATSNEW.RDM on the generated diskettes. NEW FEATURES AND UPDATES: This section details the new features and problems fixed by the contents of the Compaq Support Software Diskette v3.01A for OS/2 2.x or later. 1. Compaq Array Configuration Utility for Win-OS/2 This utility is used to configure Disk Arrays and RAID volumes on SCSI drive storage systems connected to Compaq SMART-2, SMART-2/SL, SMART-2/DH, Fibre Channel Host and Remote Controllers. It provides an intelligent and user friendly way to configure and manage the above mentioned array controllers. It provides facilities to easily expand or modify drives connected to the Array controllers. This utility also supports online configuration of drive arrays and RAID volumes. 2. Compaq Fibre Channel Controller Driver for OS/2 The Compaq Fibre Channel driver for OS/2, CPQFCAL.ADD v1.00 supports the Compaq Fibre Channel Storage Systems on OS/2. The Compaq Fibre Channel Storage System consists of Compaq Fibre Channel Host controller and Compaq Fibre Channel Array controller connected on a Fibre Channel Arbitrated Loop (FCAL). 3. Compaq Network Fault Tolerant Support for OS/2 Network Fault Tolerance is achieved on Compaq servers by configuring a redundant network controller that devotes itself to backing up the controller that is currently "operational" on the same Ethernet segment. In the event of a network failure either due to a wire fault or an internal hardware failure, the backup controller takes over transparently. Sensing the failures and switching to the backup controller is done with the Compaq Fault Tolerant Feature. 4. Compaq Array Driver updates for OS/2 The Array driver, CPQARRAY.ADD v3.30 has been updated to fix a potential hang problem on Compaq servers that support the Integrated Management Log (IML). The Array driver, CPQARRAY.ADD V3.30 has been updated to support Compaq Array Configuration Utility for Win-OS/2 Version 1.00. 5. Compaq IDE Driver updates for OS/2 The Compaq EIDE driver for OS/2, CPQEIDE.ADD v1.15 has been updated to fix a potential 'Trap D' that occurs on an OS/2 Warp system with more than 12 hard disk drives and Fixpak 32 (XR_W032). The Compaq EIDE driver for OS/2, CPQEIDE.ADD v1.15 has been updated to fix the below message appearing even if the IBM1S506.ADD entry does not exist in CONFIG.SYS. "CPQEIDE : Unable to allocate resources. Driver will be unloaded. Please remove IBM1S506.ADD from CONFIG.SYS, if present." The Compaq EIDE driver for OS/2, CPQEIDE.ADD v1.15 has been updated to fix a problem in reporting the Device Type to Compaq Insight Manager (CIM). 6. Compaq NetFlex-3 Driver for OS/2 update The NetFlex-3 driver for OS/2, NETFLX3.OS2 v2.30 supports Network Fault Tolerance. Network Fault Tolerance is achieved on Compaq servers by configuring a redundant network controller that devotes itself to backing up the controller that is currently "operational" on the same ethernet segment. In the event of a network failure either due to a wire fault or an internal hardware failure, the backup controller takes over transparently. Sensing the failures and switching to the backup controller is done by the NetFlex-3 device driver. This feature is supported in both on Half & Full Duplex modes of operation. 7. Compaq NetFlex-3 Driver for DOS updates The NetFlex-3 driver for DOS, NETFLX3.DOS V1.75 has been updated to fix a problem with the combination of IBM-LSP/Vines protocols. The NetFlex-3 driver for DOS, NETFLX3.DOS V1.75 has been updated to reduce the physical size of the driver (effective reduction of 18,624 bytes). 8. Compaq Token Ring ISA Driver for OS/2 CPQTRISA.OS2 v1.15 has been updated to fix a problem with file transferring using the LAN services. 9. Compaq Token Ring PCI Driver for OS/2 CPQTRPCI.OS2 v1.15, has been updated to fix the following problems: - Inability to receive files of size greater than 1MB on a Deskpro 6000. - Inability to initialize when the SPEED keyword in PROTOCOL.INI file was set to 4Mbps. - Accepting of invalid values for the DISABLEFIFO keyword in PROTOCOL.INI without displaying error messages. 10. Compaq 3COM PCI Driver for OS/2 Update TL3C3X9.OS2 v3.25, has been updated to fix the following problems: - Inability to receive files of size greater than 1MB on a Deskpro 6000. - Inability to initialize when the SPEED keyword in PROTOCOL.INI file was set to 4Mbps. - Accepting of invalid values for the DISABLEFIFO keyword in PROTOCOL.INI without displaying error messages. 11. Compaq Token Ring ISA Driver for DOS CPQTRISA.DOS driver v1.07, has been updated to fix the following problems: - Unloading of the driver when a wrong keyword is entered in PROTOCOL.INI. 12. Compaq Token Ring PCI Driver for DOS CPQTRPCI.DOS driver v1.07, has been updated to fix the following problems: - Trapping of the driver when receiving frames in an FTP session Windows for Workgroups environment. - Unloading of the driver when a wrong keyword is entered in PROTOCOL.INI. - Accepting out of range values for the keyword SPEED in PROTOCOL.INI. 13. Compaq BIOS-32 Driver for OS/2 update The Compaq BIOS-32 Driver, CPQB32.SYS v2.05 has been updated to log IML events related to System Fatal Fault (SFF). The Compaq BIOS-32 Driver, CPQB32.SYS v2.05 has been enhanced to prevent an NMI from getting generated when a PCI slot switch is toggled. 14. Compaq OS2APIC.PSD Driver for OS/2 update The Compaq OS2APIC driver for OS/2, OS2APIC.PSD v2.60 has been updated to support additional command line options. 15. Compaq Remote Insight Board Driver update for OS/2 The Compaq Remote Insight Board Driver for OS/2, CPQRIB.SYS v2.05 has been updated to fix the following problem: Inability to manage the OS/2 server from Compaq Insight Manager (CIM) using a Compaq Remote Insight board with firmware Version 1.10 and Point-to-Point Protocol (PPP). HOW TO USE: 1.Download the Softpaq to an empty directory on your hard drive and change to that directory. The file that is downloaded is SP4716.EXE. 2.From that drive and directory, execute the Softpaq file: SP4716 [ENTER] The following files should be created: QRST5.EXE 276549US._01 276549US._02 276549US._03 SP4716.TXT 3. Obtain 3 formatted 1.44-MB diskettes. 4. To create the diskettes, run QRST5 and follow the on-screen instructions. 5. After the diskettes are created, you may delete the downloaded file SP4716.EXE and the other files created on your hard drive if you wish. 6. Refer to README.1ST on the generated diskettes for installation instructions and additional information. Copyright 1998, Compaq Computer Corporation. All rights reserved. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.