SOFTPAQ NUMBER: SP32172

PART NUMBER: N/A 
FILE NAME: N/A
TITLE: R5500XR Firmware V2.02b
VERSION: V2.02 Rev b
LANGUAGE: English

CATEGORY: RomPaqs

DIVISION: Systems

PRODUCTS AFFECTED: R5500XR

Systems Updated:
- ProSignia, ProSignia VS, ProSignia 200/300/500, Prosignia Server 720/740
 -Proliant800/850R/1000/1200/1500/1600/1850R/2000/2500/3000/4000/4500/5000/5500/6000/6500/7000/8000/8500/ML110/ML150/ML310/ML330/ML350/ML370/ML530/ML570/DL140/DL145/DL320/DL360/DL380/DL385/DL560/DL580/DL585/DL740/DL760, Rack Mountable Proliant Servers or Systempro, Systempro/e, Systempro/LT, Systempro/XL

Options Affected: N/A

OPERATING SYSTEM: Microsoft Windows 95/98/NT4/WIN2000/XP

SYSTEM CONFIGURATION: N/A

EFFECTIVE DATE: January 02, 2006

ELECTRONIC DISTRIBUTION ALLOWED: Yes

SOFTPAQ UTILITY VERSION: 5.1

SUPERSEDES:SP29016 R5500XR Firmware V2.00 and SP30339 R5500XR firmware v2.02

DESCRIPTION: Firmware V2.02b for R5500XR Models

The R5500XR firmware update is designed to upgrade the firmware of the  following R5500XR models to v2.02b.
- 326529-D71 NA/Japan
- 326529-B31 Intl

Fixes
The following issue has been resolved with V2.02b.  The Fixes in 2.02b remain identical as in v2.02 listed below.  This R5500 firmware v2.02b was issued ONLY to correct a an error in a file name.

- Fixed a problem with the Scheduled On delay being incorrect when large delays greater than 1092 minutes are entered.  
- Fixed a problem with small auto-on delays under 10 seconds all being set to 10 seconds and failing to maintain the original auto-on delay stagger timing when sending the Load Dump & Restart cmd (0x8A). Now the minimum off time of 10 seconds is added to the auto on delays so the any staggered outlet on timing is maintained.
- Fixed a problem with the auto-on delays getting added to scheduled ON (0x91 cmd) delays when the command was sent for a single outlet. Now the auto delays are only added to the timer if the command is sent to all outlets.
- Added code to display the restart pending timer of a LD&R cmd (0x8A) in the scheduled on timer field of the status block.
- Fixed a bug with auto on delay command handler failing to range check delays. Now delays must be between -1 & 32767 otherwise the command is NAck'd.
- Added hystersis to the battery disconnected alarm to fix a problem with the battery disconnected event being logged repetitively if the battery voltage began to drop off due to extremely bad batteries or an improper battery connection.
- Added a new event BATT_FAULT_FAIL_FLOAT_EVT (1102) to distinguish between a bad battery being detected in REST mode and one being detected during the first 24hrs of the charge cycle. There is already an event for a REST mode failure. 
- Added XCP Meter 92, Line Event Count to the XCP meter block. Counter is incremented with any transfer to battery and is stored in non-volatile memory.
- Fixed a bug that could inhibit the UPS from completing its powerdown sequence correctly when high line is present and then removed while the UPS is operating in Standby mode.

HOW TO USE:
1. Download the Softpaq to a directory on your hard drive and change to that directory. This executable file is downloaded as a self extracting compressed file.  Run the file to extract the required flash utility and firmware.

2. From the specified drive and directory, execute the Flash utility and follow the on-screen instructions. (See Note)*

*Note: Use the detailed Word document instructions located within the extracted files to perform the Firmware Flash Procedure.  
 
Copyright 2005, HP Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.